Home > An Unknown > An Unknown Error Prevented The Emulator From Accessing The Processor

An Unknown Error Prevented The Emulator From Accessing The Processor

I did not have any other option for .gel file for DSP. What is the difference between the USB 2.0 JTAG Emulator and the USB560 JTAG Emulator? Search the wiki or go to useful pages for SDOWP, Compilers, CCSv3, CCSv4, CCSv5, CCSv6 Reply Cancel Cancel Reply Suggest as Answer Use rich formatting Prodigy 50 points Zengli Yang Nov It is recommended to RESET EMULATOR. weblink

And then selectedBeagle_Omap35xx_CortexA8.gel for ARM. The targets should then be power cycled or hard reset followed by an emureset and reconnect to each target. The install seemed to go correctly. Would there be any difference in speed for the USB560 and the USB 2.0?

DM648 Davinci Guru 10355 points Eddie3909 Hi The error below occasionally happens but unfortunately it is getting so frequent that I've got to find out why. The targets should then be power cycled >>>or hard reset followed by an emureset and reconnect to each target. >>> >>> >>> >>>Reset emulator options halt the whole CCS application. >>Any First, select the "Register Now" link on the login box. Use of the information on this site may require a license from a third party, or a license from TI.

These are not supported by XDS510-class emulators. I also deleted all the Debug lunches for all the projects. It is recommended to RESET EMULATOR. Could this be a software issue with Code Composer or the emulator?

TI CCS v3.1 and C672x issue with USB560, LAN560 and PCI560 emulators - CCS hangs on connect LIKELY CAUSE: CCStudio v3.1 updates applied after the C672x update from TI overwrites a When I click on Debug Active Project, I get following error Exception occurred during lunch. Yes - force CPU ready (might corrupt the code) Disconnect - disconnect CCS so that it can be reset Retry - attempt the command again Again, if I execute lpmOFF followed There is a bug in the CCS v.3.3 SR2 update, which should only be limited to devices that have a C64x+ and/or ICE_PICK devices defined in CCSetup (i.e.

These devices are shown below with the prefix (#). - We cannot support the MPSD devices C30-32 as well as the older C4x and C5x DSP's. disable and then re-enable your NIC card on the PC that you are using. 2. So, in summary, we can support all devices below, one way or another, except those marked with (x). (x)TMS320C30-32 (#)TMS320VC33 (x)TMS320C4x (x)TMS320C5x (*#)TMS320F24x (*#)TMS320F240x (*)TMS320C27x (*)TMS320F280x (*)TMS320C54x (*)TMS320C55x (*)TMS320C6000 (*)TMS320C64x (*)TMS320C67x It is recommended to RESET EMULATOR.

Reason: Failed to load program 'cvDFT.out' on any of the targets. Get More Information It's very annoying, especially when combined with the other problem I am trying to figure out in which the logtrace window does NOT work on the first run of a program Do Blackhawk emulators support +3.3V and +5V JTAG interface (14 Pin)? If you haven't read it in awhile, please read it again to see if any updates were made.

We would like to access the USB 2.0 JTAG Emulator from remote computers. have a peek at these guys Can you please do "Test connection" in CCS IDE with your custom board & emulator ? All of our USB emulators are backwards compatible with USB 1.1. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations

Some of XDS560 features include HS RTDX and faster code download. Later I removed all the .gel files. Follow Us TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | m.ti.com (Mobile Version) TI is a global semiconductor design and manufacturing company. check over here When I tried to Debug Active Project.

This will disconnect each target from the emulator. This will disconnect each target from the emulator. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at

The ICEpick_C driver and CCS setup was modified by TI and writes BAD data into the registry for CCSetup.

Our testing has produced the same results in performance as the TI PCI card (no loss in performance). Did you try the "Test connection" in CCS with your emulator ? ------------------------------- Regards, Shankari ------------------------------------------------------------------------------------------------------- Please click the Verify Answer button on this post if it answers your question. -------------------------------------------------------------------------------------------------------- The targets should then be power cycled or hard reset followed by an emureset and reconnect to each target. By being able to run in XDS510-mode we can support older versions of TI Code Composer and devices such as the VC33.

I have put a breakpoint before a loop. Do you support programming of the C24x and C28x on-chip flash? TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these http://crearesiteweb.net/an-unknown/an-unknown-error-occurred-while-accessing-flash.html If  I run the prog without breakpts, the prog runs , but I do not get any o/p and whenever I try to halt the execution, I get the error. 2.

You do not need CCS installed on this machine, but it has to be connected to the LAN. I am often having problems with the jtag connection, and the error message is reported below: /Error connecting to the target: Error 0x80000200/-1060 Fatal Error during: OCS, An unknown error prevented TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these everything is fine.

This will disconnect each target from the emulator. Products Advanced JTAG Emulators Bus Analyzers & Programmers Adapters & Pin Converters Applications & Software JTAG Accessories Services Hardware Design Software Development Embedded Emulation Consulting Support Downloads Troubleshooting Submit Support Request I am not able to load my code which is different than the example code used to remove the DSP from reset mode and connect the CCS to it. I recently bought a 5509 EVM from Spectrum Digital.

The targets should then be power cycled or hard reset followed by an emureset and reconnect to each target.